Views: 0 Author: Site Editor Publish Time: 2026-11-16 Origin: Site
A low air pressure warning on a HOWO truck should never be ignored. Unlike the hydraulic brakes used in most passenger cars, heavy-duty trucks commonly rely on compressed air to operate their service brakes. If the system cannot maintain sufficient pressure, the vehicle's braking performance and parking brake operation may be affected.
For truck drivers and fleet operators, understanding the air brake system is an important part of keeping a vehicle safe and roadworthy.
It also matters when buying a used HOWO truck. A vehicle may start normally, shift smoothly and look well-maintained, yet still have problems with its air compressor, brake chambers, air lines or control valves.
This guide explains how the HOWO truck air brake system works, the warning signs worth paying attention to, and what buyers should ask a qualified technician to inspect before purchasing a used truck.
Safety note: This article provides general technical information. Brake system design, operating pressures and inspection procedures vary between HOWO models. Always follow the specific vehicle's manufacturer documentation and have safety-critical repairs performed by qualified personnel.
Many HOWO heavy-duty trucks use a compressed-air braking system.
Instead of using hydraulic fluid to transmit braking force, the system stores pressurized air and uses it to control mechanical braking components at the wheels.
The basic process can be divided into five stages.
The engine drives an air compressor, which takes in air and compresses it.
The compressed air is supplied to the vehicle's air system.
A governor controls when the compressor builds pressure and when it stops supplying additional air.
The operating pressure range depends on the particular vehicle and its air system components.
Compressed air naturally contains moisture.
If water enters the braking system, it can contribute to corrosion, damage valves and, in freezing conditions, create blockages.
An air dryer helps remove moisture before the compressed air reaches the storage reservoirs.
Keeping the air dryer in good condition is particularly important for trucks operating in cold or humid environments.
The truck stores compressed air in reservoirs, commonly called air tanks.
These tanks provide the air supply needed for braking and other pneumatic functions.
Many heavy trucks use separate brake circuits to improve system redundancy.
For example, selected HOWO configurations use a dual-circuit compressed-air service brake system.
The exact reservoir arrangement and circuit layout should be confirmed for the specific model.
When the driver presses the brake pedal, a control valve regulates the compressed air delivered to the service brake chambers.
Inside a conventional pneumatic brake chamber, air pressure acts on a diaphragm or piston.
This force is transferred through the brake mechanism to apply braking force at the wheels.
The actual mechanical arrangement depends on whether the vehicle uses drum brakes, disc brakes or another approved configuration.
When the driver releases the pedal, the service brake chambers release the applied air pressure and the braking mechanism returns toward its released position.
Many heavy-duty trucks use spring brake chambers for parking and emergency braking functions.
This is an important distinction from the service brake.
While compressed air applies the service brakes, spring brake systems generally use compressed air to hold a powerful mechanical spring in the released position.
When the parking brake is applied, the spring provides the force needed to hold the vehicle.
If pressure in the relevant circuit becomes dangerously low, the spring brake may apply automatically, depending on the system design.
This is why a low air pressure warning is a serious safety issue, not just an inconvenience.
Understanding the basic components makes it easier to recognize what may be wrong when a warning appears.
Component | Main Function |
|---|---|
Air compressor | Produces compressed air |
Air governor | Controls the compressor's pressure cycle |
Air dryer | Removes moisture and some contaminants |
Air reservoirs | Store compressed air |
Brake pedal valve | Controls service brake air delivery |
Brake chambers | Convert air pressure into mechanical force |
Spring brake chambers | Provide parking brake force |
Protection and relay valves | Control and distribute air between circuits |
Air lines and connections | Carry compressed air through the system |
ABS components, if fitted | Help control wheel lock during braking |
Not every HOWO truck uses the same supplier, valve layout or electronic control system.
Older HOWO 371 models, newer HOWO TX models and other variants may have different braking components and control arrangements.
For replacement parts or maintenance planning, the vehicle identification number and actual component specifications are more reliable than the model name alone.
Problems with an air brake system do not always appear as a complete loss of braking.
Some develop gradually.
An air leak may initially be noticeable only when the truck is parked. A weakened compressor may take longer to build pressure. A faulty air dryer may allow moisture to collect in the reservoirs.
The following symptoms deserve attention.
A low air pressure warning is one of the most important alerts on a heavy-duty truck.
It indicates that the pressure in a monitored part of the system has fallen below the required level.
Possible causes include:
Air leakage from pipes or connections.
Problems with the compressor or governor.
Faulty air system valves.
Excessive air consumption.
Problems within the air dryer or associated components.
A warning may appear temporarily during initial system pressurization after a vehicle has been standing. It should clear in accordance with the manufacturer's instructions before the truck is driven.
If the low air pressure warning comes on while driving, bring the vehicle to a controlled stop in a safe location as soon as conditions allow. Do not continue normal driving or wait for the spring brakes to apply automatically.
Have the problem assessed before the vehicle returns to service.
A properly functioning air system should build and maintain pressure within the manufacturer's specified operating requirements.
If the pressure takes unusually long to rise after starting the engine, the system may need inspection.
Possible causes include compressor problems, excessive leakage, a malfunctioning governor or restrictions within the compressed-air system.
It is important not to assume that the compressor itself is defective simply because the pressure builds slowly.
A technician needs to check the wider system.
Some release of air is normal during brake operation or air dryer purging.
However, continuous hissing or recurring air loss from an unexpected location may indicate a leak.
Potential problem areas include:
Air hose connections.
Reservoir fittings.
Brake chambers.
Pneumatic valves.
Trailer air connections.
Even a relatively small leak can become more serious as components wear or the system is repeatedly pressurized.
If an air leak is suspected, the vehicle should be inspected before further operation.
A truck's compressor normally operates within a controlled pressure range.
If the compressor repeatedly cycles more frequently than expected, it may indicate that the air system is losing pressure or consuming air abnormally.
Possible causes include leakage, faulty valves or governor-related problems.
The cause should be confirmed through professional inspection rather than by replacing parts at random.
An ABS warning light requires a different interpretation from a low-pressure warning.
ABS, or the Anti-lock Braking System, helps prevent wheel lock under certain braking conditions.
If the ABS warning remains illuminated after the normal startup check, there may be a problem with the ABS system.
Possible causes include wheel-speed sensor issues, wiring faults, electronic control faults or other ABS-related problems.
An ABS fault does not automatically mean that all service braking has failed, but it may mean that anti-lock functionality is unavailable.
The vehicle should be assessed according to the manufacturer's instructions, and any associated red brake warning or low-pressure condition requires particular attention.
Not every braking problem triggers a dashboard warning immediately.
Other signs can include:
The truck pulling to one side while braking.
Increased stopping distance.
Uneven braking performance.
Unusual noise from wheel-end components.
Abnormal brake temperature.
Parking brake operation that does not behave as expected.
These symptoms can have several possible causes, including mechanical brake defects, tire problems or pneumatic system faults.
A qualified technician should investigate the underlying cause.
Warning or Symptom | Possible Problem | Recommended Response |
|---|---|---|
Low air pressure alarm while driving | Insufficient pressure, leakage or air supply problem | Stop safely and arrange professional inspection |
Air pressure fails to reach operating range | Compressor, governor, valve or leakage issue | Do not depart until the system is verified safe |
Continuous unexpected air hiss | Air line, valve or chamber leakage | Have the leakage assessed before operation |
ABS warning remains on | ABS sensor, wiring, controller or related fault | Obtain fault diagnosis and follow vehicle safety guidance |
Parking brake fails to release normally | Insufficient release pressure or component problem | Do not force movement; seek qualified assistance |
Truck pulls to one side during braking | Uneven brake force or another mechanical fault | Stop operating and have the braking system inspected |
Repeated moisture in air reservoirs | Air dryer or drainage system problem | Arrange professional air-system maintenance |
This table identifies possible causes rather than providing a remote diagnosis. Multiple faults can produce similar symptoms.
This is a common question from drivers and used truck buyers.
However, there is no single operating pressure value that should be applied to every HOWO model.
The correct operating range depends on the vehicle's air compressor, governor, brake circuit design and manufacturer specification.
As an example of why regional figures should not be generalized, the Oregon Commercial Driver Manual describes typical North American air brake pressure controls and low-pressure warning requirements.
Those values are useful for understanding conventional air brake systems, but they should not automatically be treated as the specification for a HOWO 371, HOWO TX or another Chinese export truck.
Before checking a vehicle, identify:
The exact HOWO model and production year.
The applicable manufacturer's brake system documentation.
The required normal operating pressure range.
The approved low-pressure warning threshold.
The manufacturer's pressure build-up and leakage test procedures.
For imported used trucks, a technical inspection report should confirm that the actual braking system meets its specified operating requirements.
A pressure gauge reading should never be interpreted without reference to the correct vehicle specification.
Used heavy-duty trucks may have operated under demanding conditions for several years before resale.
Long-distance transport, construction work, frequent braking and exposure to moisture can all affect brake system components.
However, a truck's age alone does not reveal its true mechanical condition.
Air lines and fittings can deteriorate through vibration, heat exposure, physical damage and normal wear.
Poorly supported hoses may also rub against surrounding components.
These conditions can eventually contribute to leakage.
An ineffective air dryer may allow excessive moisture to pass into the compressed-air system.
Over time, water and contaminants can affect valves and other pneumatic components.
The problem can be especially serious in freezing temperatures.
Brake linings, drums, discs, actuators and adjustment mechanisms require periodic inspection.
Excessive wear or incorrect adjustment can affect braking performance, even when the air supply itself is functioning correctly.
On some used trucks, the condition of previous repair work deserves close attention.
A component may have been replaced with an unsuitable part, or damaged air lines may have been routed incorrectly.
This is one reason why buyers should request a professional inspection rather than relying entirely on a seller's statement that the brakes work normally.
For an overseas buyer, the braking system should be included in the vehicle's pre-purchase inspection.
This is particularly important when the vehicle will be shipped internationally and may not be inspected personally before payment.
The following checklist is intended for purchasing decisions, not for unsupervised mechanical testing.
Inspection Item | Information to Request |
|---|---|
System identification | Actual brake configuration and relevant component information |
Dashboard and pressure gauges | Video showing normal pressure build-up and warning behavior |
Air leakage assessment | Results of a manufacturer-appropriate professional leak test |
Compressor and governor | Inspection findings and any relevant repair history |
Air dryer and reservoirs | Maintenance condition and evidence of abnormal moisture |
Service brakes | Professional assessment of braking performance and wear |
Parking brakes | Confirmation of correct operation |
ABS, if fitted | Diagnostic status and any recorded faults |
Trailer air connections | Condition and compatibility with intended trailer |
A short video of a truck moving around a vehicle yard does not necessarily demonstrate that the braking system is in good condition.
A more useful inspection record can show the dashboard before startup, the pressure build-up process and the system's operation after reaching the correct pressure.
The video should identify the actual vehicle, preferably using its chassis number or another verifiable identifier.
This helps buyers connect the inspection materials to the truck being offered.
For larger purchases or older vehicles, an independent inspection can provide additional reassurance.
The inspector should be qualified to evaluate heavy commercial vehicle brakes and follow the correct manufacturer procedures.
Buyers should avoid requesting dangerous demonstrations or attempting to disconnect pressurized brake lines, manually release spring brake chambers or adjust brake components themselves.
These operations can cause serious injury if carried out incorrectly.
Good maintenance is essential for safe heavy-duty truck operation.
The appropriate schedule depends on the model, mileage, driving conditions and manufacturer requirements.
Check the condition of the air dryer and service it according to the approved maintenance schedule.
Excess moisture or contamination in the air system may indicate that attention is required.
Air reservoirs and their associated drainage equipment should be checked according to the manufacturer's procedures.
The inspection should identify signs of corrosion, physical damage, abnormal moisture or leakage.
Brake chambers and related components should be examined for damage, leakage and correct operation by qualified personnel.
Spring brake chambers contain powerful springs and can be dangerous to disassemble.
The pneumatic system is only one part of a complete braking system.
Brake friction components, mechanical linkages, drums or discs also require regular maintenance.
For fleet operators, keeping records of brake inspection dates, component replacement and recurring faults can help identify patterns before they become more serious.
A documented maintenance history is also valuable when the truck is eventually sold.
When buying a used HOWO truck from China, customers often focus on engine horsepower, mileage, transmission and purchase price.
Those factors matter, but the braking system deserves equal attention.
A truck with a strong engine and attractive exterior can still require significant work if its compressed-air system has been poorly maintained.
International buyers should consider the availability of replacement brake components and qualified maintenance services in their destination country.
It is also worth confirming the vehicle's braking specification and compatibility with any semi-trailer that will be used.
For tractor trucks, the trailer air brake connections and the complete tractor-trailer braking system are particularly important.
A suitable truck is not simply one that can pull the load. It must also be capable of safely controlling and stopping the complete vehicle combination.
Ant Automobile supplies new, used and refurbished heavy-duty commercial vehicles from China, including SINOTRUK HOWO tractor trucks and dump trucks.
Our product range covers different configurations for freight transportation, container hauling, construction and other commercial applications.
Buyers can explore:
When purchasing a used HOWO truck, we encourage customers to request information about the actual vehicle, including its specifications, condition, identification details and available inspection materials.
Inspection arrangements and documentation can be discussed according to the vehicle and customer requirements.
Looking for a used HOWO truck from China?
Contact Ant Automobile to discuss available configurations, vehicle information and export quotations.
A HOWO air brake system uses compressed air stored in reservoirs to operate its service brakes. The compressor supplies air, control valves regulate pressure, and brake chambers convert air pressure into mechanical braking force.
Possible reasons include air leakage, insufficient compressor output, governor problems, faulty valves or excessive air consumption. If the warning appears while driving, stop safely and have the system inspected before resuming operation.
Loss of sufficient pressure can reduce braking capability. Depending on the system design and which circuit is affected, spring brakes may also apply. Drivers should never rely on automatic spring brake application as a normal stopping method.
No. An ABS warning generally indicates an issue affecting the anti-lock braking system. A low air pressure warning indicates a problem with the compressed-air supply or monitored pressure. Both require appropriate attention, but they identify different conditions.
Possible symptoms include continuous unexpected hissing, abnormal pressure loss or frequent compressor cycling. These signs require proper inspection because the same symptoms can have different causes.
No. Air brake configurations vary according to model, production year, market and installed equipment. The specific vehicle documentation should be used when checking pressure limits, components and maintenance procedures.
In addition to the engine, gearbox and chassis, request a professional assessment of the air brake system, brake chambers, air dryer, parking brakes, brake friction components and ABS where fitted.
Do not continue normal operation. If the warning occurs while driving, bring the truck to a controlled stop at a safe location as soon as possible and arrange inspection. The vehicle should not return to service until the fault has been addressed and safe operation confirmed.